Announcement

Collapse
No announcement yet.

new gun not spraying

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Guest's Avatar
    Guest replied
    post some pics ... it is nice to see what can be done with a hobby gun from a new pc

    Leave a comment:


  • rlanigan
    replied
    THANKS ALL.
    I readjusted psi to 20 with 15 after trigger pulled,
    dumped the cup to just under 1/4 full...
    screwed air adj in and out and WOW,
    no more cluping or sumping powder...
    ;nice fine spray. just did 2 pieces and look great.

    slight orange peel but next post is on finishing...
    Bob

    Leave a comment:


  • rlanigan
    replied
    THANKS ALL.
    I readjusted psi to 20 with 15 after trigger pulled,
    dumped the cup to just under 1/4 full...
    screwed air adj in and out and WOW,
    no more cluping or sumping powder...
    ;nice fine spray. just did 2 pieces and look great.

    slight orange peel but next post is on finishing...
    Bob

    Leave a comment:


  • rkolpack
    replied
    Looks like you need a little more air pressure and a little less powder in the cup. When I put close to that much PC in the cup that is the exact thing that happens.

    Leave a comment:


  • rlanigan
    replied
    Caswell kit, of course,
    I shook the can good, funneled contents into plastic lab bottle with smaller mouth to more easily load cups without spilling. loaded cup 1/2 full and shook up a bit more but not much.
    powder went on about 1/4 inch thick, had to knock it off, it kept a coat on so as they were test pieces, I baked them anyway, came out ok but thick coated. looked like dipped in liquid rubber.

    I will try again tonight, keep the help coming.

    Thanks,
    Bob

    Leave a comment:


  • mcaswell
    replied
    Sounbds like the powder is clumping. Try shaking the cup with the lid on to 'airiate' the powder.

    It's a bit like putting flour through a sieve to make the cake lighter.

    Leave a comment:


  • Guest's Avatar
    Guest replied
    if is caswell's gun they will help you out with tech ... the gun's have a 1 year warn. on them

    Leave a comment:


  • rlanigan
    replied
    I bought the 100 buck hobby kit,
    the gun was at level,
    through out blobs of powder, not like any other sprayer Ive used,
    was like dumping the can on it....

    bob

    Leave a comment:


  • remotestartdepot
    replied
    Originally posted by jtagger19
    I don't know what gun you have
    but I use mine at 15-20Psi
    try not to point down while dusting
    make sure you don't have the dust control fully open
    Dust control? What is that? Is it a setting on the gun?

    Leave a comment:


  • jtagger19
    replied
    I don't know what gun you have
    but I use mine at 15-20Psi
    try not to point down while dusting
    make sure you don't have the dust control fully open

    Leave a comment:


  • rlanigan
    started a topic new gun not spraying

    new gun not spraying

    Hi all,
    Just got my PC kit. Been reading up a while before I purchased the PC kit. Sounded pretty straight forward.

    Prepped some test parts, made a spray box, hooked everything up..

    The powder comes out in some nice huge blobs, air at 12lb as it goes to 10 as the trigger is pulled, air screw on gun screwed all the way in, system on, ground clipped, foot switch engaged, pulled trigger.
    I think I could have gotten better coverage just dumping the powder out of the can.....

    I pulled the trigger 4-5 times thinking just work in the gun. about 1/2 can had come out and piled on the bottom tray of the booth, (thank god I used your trick to ground a flat pan on the botton for recovery...

    No way I can get an even coat out of this sprayer.

    HELP
    Bob
Working...
X